Fire Retardants Texas - Fort Worth/Dallas based

TEST	MATERIAL TESTED 100%Cotton / 100%Polyester	RESULTS
CFR 1632.4 (FF 4-72) FAR 25.853 a & b CALIF 1237.1 NFPA 701 CAL TECH 117-F NY-NJ PORT BOSTON	Mattress Ticking / Mattress Pads Upholstery Textiles Aircraft Interiors Draperies Wall Coverings Cotton Muslin Fabrics Films	Class B Class A Passed Passed Passed Passed

	TECHNICAL DATA Interior Fire Retardant Spray Coating for Fabric & Textiles

PRODUCT DESCRIPTION:    Aqueous Based Resin

PRODUCT ANALYSIS
Total Solids	18%		PH	6.4
Weight per gallon	9.1 lbs		Flash point	Non-Flammable
Specific gravity	1.104		Color	Water clear at 78°F. - Slight haze at 50°F. or lower
Volatability	Non-Volatile		Solvents	Water(Contains no petroleum or derivatives of petroleum)
Anti-Fungus	excellent Resistance		Bacterial	Good Resistance
Linear shrinkage	None		Moisture Absorption	None
Corrosive	Mildly		Toxic	None (when dry)
Insects, rodents, aspergilli And other types of molds	Excellent resistance		Termites	Excellent resistance

RECOMMENDED USE: Interior

FLAME SAFE FABRIC SAFE is a fire retardant that can be applied to all natural and most synthetic and synthetic blend fabrics, such as

Carpet	Cotton	Polyester
Draperies	Synthetic blends	Wall Coverings
Mattresses	Theater Drapes	Curtains

ENVIRONMENTAL REGULATION:

This product complies will U. S. Federal Regulations concerning the use of lead in paint and hydrocarbon emissions.

	QUICK REFERENCE FOR APPLYING FABRIC SAFE

MATERIAL	APPLICATION	COVERAGE
Textiles/Fabrics	Treat with retardant according to manufacturer’s specifications Apply with a mist applicator held 6" -8” from surface Allow to dry before use. Treat both sides where possible.	300 - 500 sq. ft. per gallon. Do not saturate, retardant will easily penetrate material.
Fabric Areas	Apply with spray applicator. Apply to all sides and interior of pillows, seat cushions and underside of chairs and sofas. Check for color fastness by apply a small amount of retardant to an obscure area	Treat until damp to touch. Turn stuffed chairs and couches over, remove back cover, treat inner parts of items, replace backing material.
Wallpaper, wall covering	Apply chemical with mist applicator or sponge.	Treat until damp.
Carpet	Apply with spray applicator.	Treat until damp.

INTERIOR : Treatment of drapes, furniture, artificial flowers, carpets and wall coverings with Fabric Safe, gives excellent protection against ignition, flame spread and afterglow. It forms a barrier which inhibits ignition of the treated material and restricts the char to the immediate area touched exposed to flame. Fabric Safe is a water-based, clear, odorless and non-toxic fire retardant. All surfaces to be treated must be clean. Due to the vast variety of textiles and fabrics, it is important to check for color fastness. This is done by applying a small amount of retardant to an obscure area and letting it dry ( a hair dryer will aid in drying). Apply retardant as it comes from the container. DO NOT DILUTE OR MIX FABRIC SAFE WITH ANY OTHER PRODUCTS. The coverage rate of Fabric Safe is 300 to 500 square feet per gallon depending on the type and weight of the material being treated. Fabric Safe, in most instances is applied with a mist applicator. A sponge can be an effective method of applying the retardant on wallpaper and wall coverings. All treated textiles/fabrics lose some of their fire retardant qualities after deep cleaning, therefore re-treatment with Fabric Safe is necessary to achieve maximum results. Pile or high tufted carpet in particular, is suitable for treatment immediately after cleaning. Be sure all materials are dry before applying Fabric Safe.

 

CAUTION:

          Product must not freeze. It must not be thinned or diluted.

OVERSPRAY:

        The overspray will not harm plants or animals. Spills can be flushed with water. A rag wetted with   bleach and water mix will clean up spotting.

CLEAN UP PROCEDURE:

          Airless Equipment.

1. Run clear water through the system until coating is flushed out. When minor sudsing on surface stops, the system is flushed.

2. Run bleach and water mix (1 part to 4 parts) through system as solvent for cleaning any residue.

            3. Repeat Step 1 if any foaming occurs in Step 2.

            4. Lubricate system as specified by equipment manufacturer to combat rusting.

If two or more applications are planned in the same day, the sprayer can be kept clean by running water through the system between applications.

          Brushes/Rollers.

              1. Clean immediately after use.

              2. Wash thoroughly with bleach and water mix (1 part to 4 parts).

SAFETY FIRST

Use approved safety devices (ropes, belts, ridge hooks, ladder, etc.) When working on steep or high areas. Take EXTREME CARE not to step on wet treated area. Surface may be slick until dry.

It is good practice to wear respirator or mask and protect hands with rubber gloves when spraying any coating or chemical. When engineered air control is not feasible, use properly maintained and properly fitted NIOSH approved respirator for solvent vapors. A dusk mask does not provide protection against vapors.

If eye contact occurs, flood with water for fifteen (15) minutes and call a physician. KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.